The ground is the other half of the story. Silverdale sits at the head of Dyes Inlet in a flat valley where Clear Creek and Strawberry Creek drain. The valley floor has a high water table and some fill; the subdivisions climb glacial till ridges on either side. Old Town is close enough to sea level that storm surges and king tides push into the lowest drains. We reach Silverdale in about 25 to 30 minutes from Port Orchard up Highway 3 past Bremerton, and the trucks go out stocked for the jobs this community generates most.
Why well house & pressure tank service is a little different in Silverdale
Homes in Silverdale on a hill above the well house or at the end of a long supply line can have a healthy pump and still poor pressure at the shower. Before anyone talks about a bigger pump we check the switch settings, the tank size and the pipe, and we will suggest a booster after the tank if that is the right answer.
Water supply is the first question we ask on a Silverdale job. Silverdale Water District serves most of the area from its own wells, and it has been expanding its boundaries, including taking over a small pocket of former Bremerton service. Homes out toward Newberry Hill, Chico and the Seabeck Highway are sometimes on Kitsap PUD community systems or private wells.
Local conditions that affect well house & pressure tank service in Silverdale
Ask a Silverdale homeowner what goes wrong with plumbing here and you will usually hear a version of this: Commercial storm drains and grease lines around the mall and restaurant corridor
Many Silverdale wells are shallow and sit close to septic drainfields and neighbors' wells, so the water table drops in late summer and the pressure tank works harder. If your gauge swings faster in August than it did in March, the tank's air charge is worth checking before the pump pays for it.
Here is a Silverdale detail that changes how we approach the job: Polybutylene supply pipe in some late-1980s Ridgetop and Island Lake homes
Older cabins and homes in Silverdale often have a well house that was plumbed decades ago and patched one fitting at a time ever since. We rebuild the manifold as one job, with unions and ball valves so the tank can be isolated without draining the house.
Signs Silverdale homeowners call us for well house & pressure tank service
Worth a call
- The well house plumbing is a patchwork of old fittings and valves that no longer close
- The pump clicks on and off rapidly whenever a faucet is running
- Water pressure surges and sags in the shower
- The pressure tank sounds dull or heavy when you tap near the top
- Air spits from the faucets before the water runs
How we handle well house & pressure tank service in Silverdale
When a Silverdale homeowner books well house & pressure tank service, the job unfolds as tell corinne what the system is doing, diagnose at the well house, flat price on your phone, replace the cluster, not just the part, run it through its cycles, then winter and maintenance advice, and you can watch and ask questions the whole way.
Read the full step-by-step for well house & pressure tank service →
Silverdale neighborhoods and areas we serve
We have worked in Island Lake, in Old Town Silverdale on Dyes Inlet and most of the Silverdale neighborhoods in between, including the homes out by Kitsap Mall and Waterfront Park and the Port of Silverdale dock.
Well House & Pressure Tank Service questions from Silverdale
How fast can you get to Silverdale for no water?
No-water calls are prioritized, with evening and weekend availability. We give you a four-hour window and a text when the plumber is on the way. Reset the well breaker once before you call; if it holds and you still have no water, we are on our way.
My Silverdale well house froze. Can you fix the plumbing?
Yes. We repair split lines, replace cracked tanks, tees and switches, and insulate and heat the building so it does not happen again next winter.
What pressure tank do you install in Silverdale?
Well-X-Trol or Amtrol, sized to your pump and your home rather than to whatever was there before. The tank comes with a new tee, switch, gauge, relief valve and isolation valve.
Can you add filtration in my Silverdale well house?
Yes. Sediment, iron and whole-house filtration go in after the pressure tank, and we size them so flow is not restricted. A recent water test tells us what to install.
What pressure should my well be set to?
Most homes run 40/60, meaning the pump starts at 40 psi and stops at 60. Single-story homes sometimes run 30/50. A home with a second floor, a long run or a filtration system usually wants 40/60 or a little higher, and the tank precharge has to match. We set both together.
Because we are local to Kitsap County, we know the water districts, the sewer rules and the soil in Silverdale. That knowledge shortens the diagnosis and keeps surprises off the invoice.